Will a Compressed Spring Eventually Lose Its Strength?

You've designed a product that relies on a spring's constant push. But you worry that over time, the spring will weaken, causing your product to fail and creating unhappy customers.

Ano, a compressed spring will lose some of its strength, or force, over time. This happens through two main processes: stress relaxation if it's held compressed, or fatigue if it's repeatedly cycled. Však, a properly designed spring loses strength in a slow, predictable way.

I learned this lesson the hard way early in my career. A customer was developing a pressure relief valve where a compression spring held the valve shut until a certain pressure was reached. The initial prototypes worked perfectly. But after a few weeks of testing under constant load, the valves started opening too early. The spring hadn't broken; it had just lost a bit of its height and force—a phenomenon called "taking a set[^1]." We had to change the material and add a special heat treatment process to make the spring stable under that constant load. It was a critical reminder that a spring's performance isn't just about day one; it's about its strength over millions of cycles or years of use.

What Happens When a Spring is Kept Squeezed for a Long Time?

You have an application where a spring must remain compressed for years. You are concerned that the constant pressure will cause it to permanently deform, losing the force needed for your device to function.

When a spring is held in a compressed state, especially at high temperatures, it undergoes a process called stress relaxation. The spring doesn't break, but it gradually loses some of its initial pushing force and may become slightly shorter. This is a predictable material behavior.

Think of stress relaxation as a form of microscopic creep. At the molecular level, the internal structure of the spring wire slowly rearranges itself to relieve some of the internal stress from being held in a compressed position. The result is a permanent, though usually small, loss of force and free height. The two biggest factors that accelerate this process are stress and temperature. A spring that is compressed very close to its physical limit will relax much faster than one with a light load. Likewise, a spring in a hot engine compartment will lose force far more quickly than one in an air-conditioned office. For this reason, výběr materiálu je rozhodující. Používáme materiály jako 17-7 PH Nerezová ocel nebo Chrome Silicon pro vysokoteplotní aplikace, protože jsou navrženy tak, aby tomuto efektu odolávaly.

Managing a Spring's Long-Term Performance

Tuto ztrátu pevnosti můžeme předvídat a minimalizovat pomocí inženýrství.

• Zvládání stresu: Dobrá konstrukce zabraňuje stlačení pružiny blízko jejího maximálního limitu po dlouhou dobu.
• Výběr materiálu: Výběr správné slitiny je zásadní pro aplikace zahrnující vysoké teploty nebo vysoké zatížení.

Does Using a Spring Over and Over Make It Weaker?

Your product requires a spring to compress and release thousands or even millions of times. You need to know if each cycle makes the spring weaker, leading to an eventual and unexpected failure.

Ano, repeatedly using a spring causes fatigue[^2], which is a gradual weakening of the material. Each cycle creates microscopic damage[^3] that accumulates over time. This can lead to a loss of force or, eventually, the spring breaking completely. This "fatigue life" is a key design parameter.

Fatigue failure is the most common reason a spring breaks in a dynamic application, like in a car's engine valves or an industrial machine. It’s very similar to bending a paper clip back and forth. The first few bends do nothing, but if you keep going, it gets weaker and eventually snaps. In a spring, every compression cycle creates a tiny amount of stress damage. The size of this damage depends on the stress range—the difference between the minimum and maximum load. A spring that is only compressed a small amount will last almost forever. A spring compressed nearly to its solid height on every cycle will have a much shorter life. This is why we pay so much attention to processing. A process called "shot peening" bombards the spring's surface with tiny steel balls, creating a protective layer of compressive stress that makes it much harder for these microscopic cracks to form and dramatically increases the spring's únavový život[^4]tps://www.acxesspring.com/life-cycle-of-a-spring.html?srsltid=AfmBOoqDZY1W2Dyw3TRHxn3VrLxtleTEaNHnSYuEj9_FajCRpcpw5ZoN)[^2] život.

Design pro dlouhou životnost

A spring's lifespan is not a matter of luck; it's a result of deliberate design and manufacturing choices.

• Kontrola stresu: Jediným největším faktorem únavový život[^4]tps://www.acxesspring.com/life-cycle-of-a-spring.html?srsltid=AfmBOoqDZY1W2Dyw3TRHxn3VrLxtleTEaNHnSYuEj9_FajCRpcpw5ZoN)[^2] životnost je rozsah provozního napětí.
• Vylepšení materiálu: Manufacturing processes can significantly increase a spring's resistance to fatigue[^2].

Závěr

A spring will lose strength, but this process is not a mystery. Through careful design, material selection, and manufacturing, we can ensure a spring performs reliably for its entire intended lifespan.

[^1]: Explore this phenomenon to prevent premature failure in your spring applications.
[^2]: Learn about fatigue to ensure your spring design can withstand repeated use without failure.
[^3]: Explore how microscopic damage affects spring performance over time.
[^4]: Learn about fatigue life to ensure your springs can handle their intended cycles.